CT710 – SKX007 to MM Conversion Case – Full Size MM300 – Black

£70.00

In stock

Save money by adding your bezel click spring below!

Material – Stainless Steel 316L

Finish Options:

  • Black – comes with a matching CT237 MM Bezel

Description – SKX007 to MM Look Conversion Case set – Full Size Iconic MM Dimensions – @ 44mm wide – 50mm lug tip to tip – 15mm thick – 20mm lugs – Front loader no case back – 20mm lugs

Check out this incredible build by @watchmods.ca on Instagram

Included with every case set:

  1. 1 x Crystal Gasket – FITTED INTO 7 BELOW
  2. 2 x 20mm Fat Spring Bars
  3. 1 x Lower Movement Gasket
  4. 1 x Top Case Gasket
  5. 1 x Bezel Click Spring
  6. 1 x Movement Holder
  7. 1 x Crystal Holder/Top Case Ring – LH Thread
  8. 2 x Rear Case Access Screws*
  9. 2 x Rear Case Access Screw Gaskets*
  10. BLACK SET ONLY – CT237 MM Black Bezel INCLUDED

* Only 1 needed – 1 Spare

Parts Compatibility Note

  • We recommend our CT208 CT209 CT228 Crowns for this case and our CT237 MM bezel. If you are using a flat insert for your build (as oem MM) our CT099 Sapphire is good. If you are using a sloping insert our CT119 Sapphire is good. Of course you are free to choose any others manufacturers parts to complete your build and they should in theory fit but we cannot be responsible if you are disappointed in the event you end up with a frankenwatch look or the bezel function/feel is not as you expected.

Information

  • A Front Loading MM Conversion Case Set with NO back. Drilled Lugs. Polished/Brushed finish. Most SKX007 parts will fit this case – Dial, Chapter Ring, Crystal, Crystal Gasket, Bezel, Bezel Insert.
  • This is our tribute to the classic MM case WITH A TWIST. It is NOT and was never intended to be a 100% exact copy of the oem case. We believe we achieved a good balance between the oem look and our unique conversion case.
  • In keeping true to the iconic MM300 this conversion case is a front loader with no back. This requires a different method of assembly but is not rocket science and worth the effort.
Please take your time to fully read the Instructions before purchase.5 minutes spent reading this spec and the instructions is recommended - click here

IMPORTANT NOTE

  • Oem and aftermarket MM SEL bracelets will not fit this case. This superb case was designed primarily for straps and not MM SEL metal bracelets. We are aware that some of the fitted rubber straps will fit – Crafter Blue is confirmed – check customer pic in this spec. This case is specifically designed to suit the NH Grey Movement Holder – The thicker black movement holder i.e. 7S26 SKX007 will not fit
  • Please take extra care not to over-tighten the rear case access screw – it can be damaged/broken if too much force is used – its is a small diameter thread (2mm) with a gasket and does not require to be super tight – simply screw it down snugly – this has been tested to 300M. Take care particularly when using the hex head screw as it may encourage you to over tighten

Water Resistance – As oem*

  •  *This case was tested to 300M during development and subsequent testing of actual production cases – no failures were recorded.

Suitability

  • Building an amazing MM look watch with the multitude of SKX007 parts available should lead to some exciting builds.

Additional info

  • A top quality MM conversion set – NOT expected to be a limited edition but the first run of 300 pcs are laser numbered. Achieve the classic timeless MM look at a fraction of the price!

2 reviews for CT710 – SKX007 to MM Conversion Case – Full Size MM300 – Black

  1. 5 out of 5

    Absolutely awesome value for money.

    I used this case as the foundation to build a MM300 and the feedback from friends and family has been that it’s probably my best mod to date – please see pics.

    Build tip. If you don’t have the correct tool to gently tighten the left hand threaded crystal housing in, screw it in to finger tight, then install the crystal as per the instructions- once that’s seated, use a case back ball placed on top of the crystal and housing and use it to tighten the housing as you would a case back (or loosen if you need to remove it in the future) it works perfectly and also prevents any slipping with a metal tool that could scratch your new case – hope that helps

    Uploaded image(s):

    Image #1 from SeikologyGrad
    Image #2 from SeikologyGrad
    Image #3 from SeikologyGrad
  2. 5 out of 5

    Absolutely awesome value for money

    I used this case as the foundation to build a MM300 Mod and the feedback from friends and family has been that it’s probably my best mod to date – please see pics.

    Build tip. If you don’t have the correct tool to gently tighten the left hand threaded crystal housing in, screw it in to finger tight, then install the crystal as per the instructions- once that’s seated, use a case back ball placed on top of the crystal and housing and use it to tighten the housing as you would a case back (or loosen if you need to remove it in the future) it works perfectly and also prevents any slipping with a metal tool that could scratch your new case – hope that helps

    Uploaded image(s):

    Image #1 from SeikologyGrad
    Image #2 from SeikologyGrad
    Image #3 from SeikologyGrad

Only logged in customers who have purchased this product may leave a review.